Ozone aging box product analysis and research - Database & Sql Blog Articles

Industrial Router Crystal 3.2*2.5mm 3225 26M (26.000MHZ) 12PF 10PPM 20PPM 30PPM

Photocoupler

Ozone aging box

/Ozone test box / ozone aging test chamber / rubber ozone aging test chamber / ozone aging test machine

ZSY-37 type

one,

Ozone aging box

Overview:

The ozone aging test chamber is one of the climate simulation test equipments. It is suitable for evaluating the vulcanized rubber and other products under static tensile deformation, exposed to air containing a certain concentration of ozone and a certain temperature environment, but without the harsh conditions under direct illumination. The adaptability test can be used for aging test of product samples by various scientific research institutions and factory and mine center laboratories. The equipment temperature controller has high precision, high stability and ensures equipment precision control.

two,

Ozone aging box

Main technical reference:

1. Ozone concentration range: 0ppm~5ppm

2, temperature range: room temperature ~ 50 ° C

3, temperature uniformity: ± 2 ° C

4, temperature fluctuation: ± 0.5 ° C

5, test piece speed: 20 ~ 25 rev / min

6, cycle motor: 25W

7, turntable motor: 370W (optional)

8, the power supply voltage: 220V

9, frequency: 50HZ

three,

Ozone aging box

Structural features:

1. The shell of the test chamber is made of high-quality cold-rolled plate and electrostatically sprayed, and the inner tank is made of high-quality stainless steel;

2. Adopt high quality and high efficiency corona discharge type ozone generator;

3. The ozone concentration is direct digital display, and the US imported ozone concentration sensor can achieve precise control;

4. The temperature of the test chamber is controlled by a temperature controller;

5. The middle part of the studio is equipped with a stainless steel turntable, and the test piece fixture can be installed on the turntable for the test piece to be tested according to the standard requirements;

6. The structure and performance of this product are more accurate and intuitive than similar products. The ozone concentration is LED digital display, with over-temperature protection and automatic power-off, short-circuit protection and other functions.

four,

Ozone aging box

Conditions of Use:

1, temperature: 15 ° C ~ 35 ° C

2. Relative humidity: ≤85% RH

3, atmospheric pressure: 86 ~ 106Kpa

4. There is no strong vibration around;

5. Direct radiation without direct sunlight or other heat sources;

6. There is no strong airflow around. When the surrounding air needs forced flow, the airflow should not be directly blown onto the cabinet;

7. There is no strong electromagnetic field around it;

8. There is no high concentration of dust and corrosive substances around;

9. In order to protect the normal operation and operation of the equipment, in addition to maintaining the level, a space of 60 cm is reserved between the equipment and the wall or the object.

Fives,

Ozone aging box

Safety Precautions:

1. To protect the safety of the equipment and test, please install an external protection mechanism and supply power according to the equipment nameplate requirements;

2. The equipment is strictly forbidden to be used for tests of flammable, explosive, toxic and corrosive articles;

3. The equipment should be installed horizontally;

4. Non-professionals shall not disassemble or repair;

5. The equipment should be reliably grounded;

6. Do not open the door or enter the box unless necessary, otherwise it may cause human injury and malfunction of the equipment;

7. The door lock of the equipment box can only be opened from the outside, and must be monitored by the person inside the box;

8, the equipment has a variety of protective measures, please check regularly;

9, there is an alarm input, should check the alarm position, turn off the power, eliminate the fault, must not force the boot;

10. Any operation of the equipment should be safe.

six,

Ozone aging box

Operation method:

1. Sequence of operation (each switch is off) Close the power switch The temperature controller will display the temperature inside the box. Press the panel power switch to start the device, then press the ozone button to set the ozone concentration, then set the temperature, and adjust the temperature control switch to the temperature to be protected (not allowed to exceed 60 degrees), and then set the time.

2. Fix the test sample on the turntable fixture, adjust the bolt, adjust to the required stretch length, and fix it.

3. Close the door, close the power switch, and activate the buttons on the panel to automatically run the device.

Note: 1. Temperature controller and ozone concentration controller. The specific operation method is detailed in the instrument manual.

2. The ozone concentration controller has a delay at the beginning of power-on, which is a normal phenomenon.

3. The measuring range of the temperature controller is: 0 °C ~ 99.9 °C, so it will not display the temperature below 0 °C.

Seven,

Ozone aging box

Daily maintenance:

1. Pull down the power circuit breaker after the test is over;

2, set the electrical accessories in case of failure to repair or replace the same type of accessories;

3. The equipment should be operated and maintained by a special person;

Note: All articles with "!" are required actions or matters of concern.

Depending on the equipment order, its performance can be slightly different from this manual.

Due to the continuous updating and development of product technology, the technical parameters and product structure release provided in this manual involve the improvement of the main performance of the product without prior notice. It is expected that the written instructions of the commissioning personnel assigned by the company will be explained. , are all part of this manual.

If the equipment is found to be insufficiency in some places and needs improvement, we sincerely hope that you can contact us and your valuable Jianshi City company's development momentum.