How to reserve a faucet for the washing machine? Renovation is a headache for most consumers, especially the decoration of the bathroom. All kinds of excuses should be reserved, especially the necessary faucets such as washing machines and bathtubs. How to reserve them? The author introduces you today: First, prepare the installation tools, check whether the supporting parts are complete before installation. Common faucet parts include: hoses, rubber washers, showers, water, kidnappers, decorative caps, etc. First of all, it is best to initially select the model of the drum washing machine you need and study the size. If you can, of course, the faucet is better near the water inlet of the washing machine. In order to achieve optimal use of the home space, this design should be based on space. How to put the washing machine to save space and use space is the first thing you should consider. After considering the spatial distribution, determine the position of the faucet. The faucet position is best than the size of the washing machine when it is allowed. In the future, you will need to replace a larger washing machine in the next few years. The faucet is not lower than the height of the washing machine. The specific height is not required to be demanding. It is better to stand and operate comfortably, so that it can adapt to various types of drum washing machines or other forms of washing machines. Do not bury the faucet's interface in the wall, as it sometimes encounters the problem of replacing the faucet. In fact, even if the faucet can be connected to a lower position, it is best not to do that. Who wants to bend and release the water? The drum type washing machine has a water receiving position that is better on the side of the washing machine. The height is generally around 1100~1300cm. 1. Use the special faucet of the washing machine and plug it directly. 2. Use ordinary faucet: the length of the inlet pipe of the washing machine is generally about 1m. One end is connected to the washing machine, and one end is connected to the faucet. The connection to the washing machine is very simple. Place the inlet pipe connection seat vertically on the inlet valve and screw it clockwise. The connection with the faucet is as follows: Step 1: Hold the connector with four screws in one hand, pull down the buckle of the inlet pipe with one hand, and separate the connector from the inlet pipe; Step 2: Confirm the white in the connector After the plastic guide sleeve and the black rubber pad are intact (if the faucet pipe diameter is too thick, the plastic guide sleeve can be removed), loosen the four screws on the connector, and rotate the upper and lower connectors to leave 3- 4 thread gap; Step 3: Connect the connector horizontally to the faucet and tighten the loosened four screws; Step 4: Tighten the 3-4 threaded connectors reserved in advance to the watertight . If it is a fully automatic washing machine, it is generally unnecessary to close it after opening, plus there is a certain water pressure, so there must be no water leakage. Generally, you should choose a threaded faucet, which is basically foolproof after tightening. However, if it is an ordinary two-cylinder washing machine, because there is no pressure, it can be used as usual when washing clothes. The general faucet can be used. How to reserve a faucet for the washing machine? â—How to choose bathroom accessories? Today's bathroom accessories include mirrors, soap tables, towel rails, towel racks, roll holders, and clothes hooks. Buy high-quality and durable bathroom hardware accessories, not only should pay attention to the brand, but also pay attention to matching, materials and coatings. First, look at the package. The three sanitary wares in the bathroom occupy the largest position in the bathroom. When purchasing sanitary hardware accessories, it is necessary to consider whether these accessories match the purchased sanitary ware. Second, look at the material. The materials of the bathroom hardware accessories in the market are probably titanium alloy, copper chrome, stainless steel chrome, aluminum alloy chrome, iron chrome and plastic. Among these materials, the quality of titanium alloy hardware is the best, the quality of plastic products is the worst, pure copper chrome products can prevent oxidation, stainless steel chrome is cheap, but the use time is relatively short. Again, look at the coating. A good coating is black and shiny, with a moisturizing feel, while a poor quality coating is dull. A good coating is very flat, and a poor quality coating will look like a wavy undulation on the surface. There are also depressions on the surface that are definitely inferior products. How to reserve a faucet for the washing machine? 1. Installation of single hole basin faucet When buying a single-handle basin faucet, you should pay attention to the diameter of the water outlet. Most of the market is now a hard tube, so you should pay attention to the height of the water inlet. The 35 working points from the basin are most suitable. When installing, be sure to choose a special angle valve, and the angle valve must be fixed with the hot and cold water pipe of the wall outlet. When you find a distance between the angle valve and the water pipe on the faucet, purchase a special extension tube to connect. Remember, don't use other water pipes to connect, because if the water pressure is too large, it will easily fall off and leak, causing damage to you. If the inlet pipe is too long to exceed the outlet pipe, you can cut off the part according to your needs. If the angle is not suitable, bend it to the position you need as needed. Remember: Do not bend hard to 90 degrees or more than 90 degrees. When installing the basin to remove water, please don't forget to buy the small interface of the faucet (the faucet is shorted). Don't forget to flush the water pipes buried in the wall before you install it. 2, shower, bathtub faucet (wall mounted) installation When you have purchased a shower, bathtub, or wall faucet, you can choose the right height to bury the water pipe. The spacing between the hot and cold water pipes must be 15 cm. Before installation, you must not forget to rinse the water pipe to avoid excessive water quality and damage to the faucet. Concealed shower, bath faucet: After purchasing the concealed faucet, the sluice spool should be pre-buried in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding. If the wall is too thin, the spool will not be buried. The plastic protective cover of the valve plug should not be easily removed when it is buried, so as to prevent the cement and other chores from damaging the valve core when it is buried. In addition, when pre-burying the valve core, you should also pay attention to the up and down and left and right directions of the valve core to avoid the valve core being buried. When the wall mounted faucet is pre-buried into the water pipe, the size is deviated, and the adjustment can be used to adjust the position. 3, the installation of thermostat Before installing the thermostatic faucet, please check if the water pipe is left hot and cold right. Remember not to connect the hot and cold water pipes incorrectly, so as to prevent the faucet from working properly. Gas and solar water heaters cannot use thermostats because the water pressure is too low. Do not forget to install the hot and cold water filter when installing the thermostat. 4, single hole kitchen faucet installation The requirements are stable, because the kitchen faucet is used frequently, and it is moved and moved, so it is easy to loosen, so the lock nut must be tightened. At present, some faucets appear on the market for the screw to increase the nut fixing. This kind of stability effect is very good. If it can solve the problem of water removal, it will be a popular trend in the future. Tension Clamp,Non-Metallic Joint Box,Oppc Cable Suspension Clamp,Oppc Cable Fittings Shandong Qingguo Optical Fiber Co., Ltd. , https://www.qgfiber.com
