1, LED life is short: the theoretical service life of LEDs produced by regular manufacturers is generally about 80,000 hours. Nowadays, many of the luminous characters have not been used enough for a year to start replacing LED modules frequently, which brings a lot of trouble and economic loss to customers and advertising producers. Solution: Purchase qualified LED single lamp particles produced by regular manufacturers (requires quality parameter description provided by the manufacturer), and make the module yourself. Don't try to buy LED single light pellets or already made modules in the electronic display market. If you need to buy a module, you should see that several resistors are installed on the module. It is best not to use a module with one resistor. The resistor acts as a current limiting function in the module and is prone to heat. Continuous use for a long time, once the resistor burns out, the module will not light up. LED lights are generally not bad. Do not throw away the module, just replace it with a resistor of the same resistance. This saves money for the production unit. In order to reduce trouble and save money, it is best to use a module with two resistors installed. In addition, you should have an understanding of the production facilities of the suppliers who make the modules, and see if they use anti-static facilities when making the modules. If there is no anti-static device attached, even if the resistor is not burnt out during use, the LED lamp is easily damaged by breakdown. 2, the color decays very fast: the color of the newly installed light word is pure and bright, and the color can be obviously dimmed after less than one year. It is very ugly to make the font red and red, green and green. Solution: The safe current of the LED light is generally 20 mA. Above this value, although the brightness will increase, the color attenuation will be significantly accelerated. Therefore, when purchasing an assembled LED module, be sure to test its output current value. Less than 20 mA is not enough brightness, and more than 22 mA affects LED life, which speeds up color decay. 3, the color is uneven, the color difference is obvious: mainly in the large-scale luminous characters made by pure white LED. In the assembly, the performance of the single module is not obvious. After the whole font is assembled, the chromatic aberration is clearly expressed. The whole face is like a map, white, blue and yellow. Solution: The white LED light is subjected to spectral separation before leaving the factory (the LEDs that have not undergone the separation and color separation are pure white, some are bluish, some are yellow), and the spectrophotometer is expensive. The general small factory does not have such equipment, so the white light produced is generally obtained by the big factory for color separation, because it is not the product of its own factory, the separation and separation will not be so careful. Some small factories simply do not separate the light. They generally pull customers at low prices. Therefore, when buying white LEDs, don't be blind and cheap. Be sure to buy LED light-emitting tube single-particle lamps or modules of the same manufacturer, same batch, and same color number to make the same batch of luminous characters. 4, the font part of the stroke, the overall suddenly does not light or when the light is not bright: after the use of a certain period of time, the local or the entire font light source begins to flash, when the light is off, it does not light until it is completely off. Most of the lighting modules currently on the market are connected by patch cords. In this way, the advertiser is quick and easy to install the lighting module. However, some new problems have also arisen. Because the connector is easily oxidized by the moisture in the air during long-term use, the contact is poor, and the partial or all circuits are instantaneously powered off or completely powered off, causing the font source to flicker or not bright. Solution: a. When the module is made, the connector is not used, and the copper tinned wire is directly connected and then soldered with activated carbon solder. b. Use artificial agate to make a fully enclosed hollow three-dimensional luminous word to isolate the light source from the air. 5, the font output power is large, energy saving is not obvious. Solution: Try to use an LED lighting module with one set of five lights, so that the number of lights has not changed, and the power is reduced by two-fifths.
Kara offers a wide range of illuminated and non-illuminated Rocker Switches.In this series,Rated current 6A,10A,16A,Ranging from 1 to 6 poles,with many styles of colors and functions. Certifications include UL, CSA, TUV, CE, and more.
Why choose us?
1)As a manufacture, all of our switch parts are made by our own factory in Ningbo. So, price is competitive.
2)We have our own UL testing lab in Taiwan, so quality can be guaranteed.
3) We can provide you with different types of rotary switches for your selection.
4) Various operating force,height and colour for one switch for your choice.
5) Safety, on-time delivery, excellent quality with competitive price.
6) MOQ: 1000pcs,mixed order acceptable, welcome trial order.
7) OEM and ODM professional design.
8) We can provide free samples for your test.
Small-Sized Rocker Switches,Round Rocker Switch,Small Rocker Switch,Mini Rocker Switch Ningbo Kara Electronic Co.,Ltd. , https://www.kara-switch.com
0 times
Window._bd_share_config = { "common": { "bdSnsKey": {}, "bdText": "", "bdMini": "2", "bdMiniList": false, "bdPic": "", "bdStyle": " 0", "bdSize": "24" }, "share": {}, "image": { "viewList": ["qzone", "tsina", "tqq", "renren", "weixin"], "viewText": "Share to:", "viewSize": "16" }, "selectShare": { "bdContainerClass": null, "bdSelectMiniList": ["qzone", "tsina", "tqq", "renren" , "weixin"] } }; with (document) 0[(getElementsByTagName('head')[0] || body).appendChild(createElement('script')).src = 'http://bdimg.share. Baidu.com/static/api/js/share.js?v=89860593.js?cdnversion=' + ~(-new Date() / 36e5)];